Enzi, A., Mynderse, J. A., 2019. "Design and experimental validation of a small-scale prototype selective laser sintering system," SN Applied Sciences, 1(1612), doi: 10.1007/s42452-019-1600-3.
Curtis, A. B., Mynderse, J. A., and Vejdani, H., 2019. "Design of a Kangaroo Inspired Hopping Robot For Unrestricted Locomotion and Controller Development," Proc. 2019 ASME Dynamic Systems and Control Conference, doi: 10.1115/DSCC2019-9083.
Mynderse, J. A., Liu, L., Gerhart, A. L., Fletcher, R. W., Vejdani, H., Jing, W., and Yee, K., 2019. “Development of an Entrepreneurial Mindset within a Three- Semester Mechanical Engineering Capstone Design Sequence based on the SAE Collegiate Design Series”. 2019 ASEE Annual Conference & Exposition.
Bowden, D. S. and Mynderse, J. A., 2019. “From Industry to the Classroom: A Low-Cost Hardware-In-Loop Simulator for Classic Controls Experiments”. 2019 ASEE Annual Conference & Exposition.
Gennert, M. A., Lofti Yagin, N., Mynderse, J. A., Jethwani, M., and Kapila, V., 2019. “Work in Progress: Building the Mechatronics and Robotics Education Community”. 2019 ASEE Annual Conference & Exposition.
Enzi, A., and Mynderse, J. A., 2017. “Optimization of process parameters applied to a prototype selective laser sintering system”. ASME 2017 International Mechanical Engineering Congress and Exposition IMECE2017.
Mynderse, J. A., Shelton, J. N., and Gerhart, A. L., 2017. “Entrepreneurially minded learning in a semester-long senior/graduate mechatronic design project”. ASME 2017 Dynamic Systems and Control Conference DSCC2017.
Patria, G. S., Rescoe, S., Bradford, W., and Mynderse, J. A., 2016. “Road wheel readiness experiment leveraging logistics engineering”. 2016 Ground Vehicle Systems Engineering and Technology Symposium.
Johns, M., Kamping, H., Krueger, K., Mynderse, J., and Riedel, C., 2016, “Setting differential pinion bearing preload using system stiffness as estimated by frequency response”. Proceedings of the SAE World Congress.
Mynderse, J. A. and Chiu, G. T.-C., 2016, "Two Degree-of-Freedom Hysteresis Compensation for a Dynamic Mirror Actuator," ASME/IEEE Transactions on Mechatronics, 21(1), doi: 10.1109/TMECH.2015.2493038.
Mynderse, J. A. and Chiu, G. T.-C., 2013, “Modeling of a dynamic mirror with antagonistic piezoelectric stack actuation,” Journal of Dynamic Systems, Measurement, and Control, 136(2), doi: 10.1115/1.4025671.
Garett S. Patria, DEMS 2017, “Model-Based Systems Engineering Application to Analyze the Ground Vehicles and Robotics Sustainment Support Strategy”.
Abass M. J. Enzi, DEMS 2017, “Optimization of Process Parameters for Improved Part Quality Using a Selective Laser Sintering System”.
David Bowden, MSMSE 2019, “Development of a Low Cost Hardware-In-Loop Simulator for Classical Controls Experiments”.
Justin Trzeciak, MSME 2019, “Design of an Automatically Adjusting Air Cell Cushion to Reduce the Risk of Pressure Sores in Wheelchair Users”.
Vincent Nicolazzo, MSMSE, “Improved flight performance through morphology changes for multirotor craft operating in non-uniform ground effect”.
Honors And Awards
2017 Henry B. and Barbara J. Horldt Excellence in Teaching Award
Faculty Research Seed Grant Award, Lawrence Technological University
Estus H. and Vashti L. Magoon Award for Excellence in Teaching, Purdue University
Laura Davidson Winkelman Fellowship, Purdue University
John M. Bruce Memorial Scholarship, Purdue University
Activities And Service
Member, American Society for Engineering Education (ASEE)
Member, American Society of Mechanical Engineers (ASME)